Cameras

There are a few steps you can take if your camera won’t connect to the Philips Hue app during setup. 

1. Make sure the camera is an appropriate distance from your router. 

If the camera is too far away or too close, you may encounter connectivity issues. Reposition your camera either closer to or further away from your Wi-Fi router or access point, and then try to connect it to the app again.  

If you have already mounted your camera and you can’t move it, you can also try moving your Wi-Fi router or access point instead. 

2. Restart your camera. 

Philips Hue Secure wired cameras: 

1. Disconnect the camera's power cable from the wall outlet.
2. Wait for 10 seconds, and then reconnect the power cable. Your camera will automatically restart.

Philips Hue Secure battery cameras: 

Press the button located at the back of your camera for 5 seconds and wait for it to restart. Release the button after the second beep.

Note that holding the button down for 10 seconds will factory reset the camera. The camera will beep a third time after holding the button for 10 seconds. 

In rare cases, you may need to reset your camera and set it up from the beginning. However, try all troubleshooting steps listed here before doing so. 

3. Make sure your home Wi-Fi is working correctly.  

Verify that the connection is up and running on a different device. If you're using a mobile phone, you can turn on Airplane mode, and then enable Wi-Fi. This will ensure you’re not using your cellular data.  

If your Wi-Fi connection is the issue, restart your router and/or modem. 

4. Restart your router. 

This will reset your internet connection. If you have Wi-Fi range extenders or repeaters, restart them as well. Each device is unique, so you may need to refer to its manual for specific instructions. In general, these are the steps to restart a router: 

1. Unplug your modem and router from power. Depending on your setup, you may have a combination modem/router or separate devices. All lights on both should be off. 
   
2. Wait approximately 30 seconds, and then plug them back in. 
3. Your devices should power on again. Wait a few minutes for the lights on the devices to stabilize. 

Once your router and modem have restarted, try to connect the camera to the app again. 

If your internet is still not working properly, contact your internet service provider to ask about the service status in your area. 

5. Check for wireless interference. 

The settings on your router or access point may cause connectivity issues. For example, if you have high firewall security or parental controls enabled, they may block new devices from connecting to your Wi-Fi network.  

See if your Wi-Fi router or access point have any of these features enabled. If so, consult the manual to see how you can exclude your camera from these restrictions. 

Your Philips Hue Secure camera may go offline due to various reasons:  

• Network issues  
  
• Loss of power 
• Old versions of the Philips Hue app 
• Camera is too hot or too cold 

Network issues refer to problems with your network itself. There are several reasons your network may lose connectivity, such as a power surge, power loss, a loose wire in your router setup, or a change to your Wi-Fi network password. 

Most of these issues are temporary — once they are resolved, your camera should automatically come back online. In rare cases, the device may remain disconnected. In this case, we recommend troubleshooting. 

Ensure that all wires are plugged in and that the lights on the front of the router are green. Check if other Wi-Fi devices are experiencing connectivity issues. Additionally, unplug your router for 30 seconds and then plug it back in to see if your camera automatically reconnects. If there are no network issues, you’ll need to investigate further. 

1. Loss of power 

1. If your camera is not connected to power — which may be a result of a power surge or loose cable — it will go offline. To check if your camera is connected to power, follow these steps: 
2. If your camera is connected to a light switch, ensure the switch is in the “on” position. 
   
3. Press the setup button on back of the camera. If it has power, you should hear a voice saying, "Entering setup mode," and the light on the camera will flash. 
4. Trigger the camera’s motion sensor. If the lights turn on, your camera has power. 
5. Check your breaker box to see if a fuse has blown. If necessary, flip the breaker back to its correct position.  
6. Once you have confirmed that the camera is receiving power, let it run. The light at the bottom should stop flashing and glow steadily, indicating that it has automatically reconnected to your network. 

2. Older versions of the Philips Hue app 

Make sure you have the latest version of the Philips Hue app. You can update your app from the App Store or Play Store. 

Your Philips Hue Secure camera may go offline due to various reasons:  

• Network issues  
  
• Loss of power 
• Old versions of the Philips Hue app 
• Camera is too hot or too cold 

Network issues refer to problems with your network itself. There are several reasons your network may lose connectivity, such as a power surge, power loss, a loose wire in your router setup, or a change to your Wi-Fi network password. 

Most of these issues are temporary — once they are resolved, your camera should automatically come back online. In rare cases, the device may remain disconnected. In this case, we recommend troubleshooting. 

Ensure that all wires are plugged in and that the lights on the front of the router are green. Check if other Wi-Fi devices are experiencing connectivity issues. Additionally, unplug your router for 30 seconds and then plug it back in to see if your camera automatically reconnects. If there are no network issues, you’ll need to investigate further. 

1. Loss of power 

If your camera is not connected to power — which may be a result of a power surge or loose cable — it will go offline. To check if your camera is connected to power, follow these steps: 

• If your camera is connected to a light switch, ensure the switch is in the “on” position. 
  
• Press the setup button on back of the camera. If it has power, you should hear a voice saying, "Entering setup mode," and the light on the camera will flash. 
• Trigger the camera’s motion sensor. If the lights turn on, your camera has power. 
• Check your breaker box to see if a fuse has blown. If necessary, flip the breaker back to its correct position.  
• Once you have confirmed that the camera is receiving power, let it run. The light at the bottom should stop flashing and glow steadily, indicating that it has automatically reconnected to your network. 

2. Older versions of the Philips Hue app 

Make sure you have the latest version of the Philips Hue app. You can update your app from the App Store  or Play Store. 

If your Wi-Fi network isn't visible in the app while setting up the camera, it could be due to various reasons, such as distance between the network and the router, wireless interference, a hidden network name, or some other problem. 

1. Ensure your Wi-Fi shows up in the Philips Hue App  

Depending on where you live you may or may not have multiple Wi-Fi networks around you. Please scroll down to the bottom of the network list in the app to check for Wi-Fi names further down. Usually, networks with stronger signals appear at the top, while those with weaker signals are located towards the bottom. 

Please be patient and allow the app sufficient time to locate your network, especially if you reside in an area with a high number of Wi-Fi networks. It may take a while for your network to appear if there are many networks in proximity. 

2. Manually enter a hidden network name 

To connect to a hidden network, follow these steps: 

• Open the app and go to the network settings 
  
• Scroll to the bottom of the network list 
• Choose "Other network" 
• Enter the name of your Wi-Fi network 
• Select the security type (WEP, WPA, or WPA2) for your network 
• Enter the password for your Wi-Fi network 

Please note that hidden Wi-Fi networks are not automatically displayed on the app list. 

3. Keep your camera and router closer together. 

4. Attempt repositioning your camera and router to a closer proximity. Even a small distance adjustment can have a significant impact on the connection. 

5. If relocating the camera is not feasible, try moving the Wi-Fi router closer instead. 

6. If the desired camera installation spot is excessively distant from the router, you may want to think about incorporating a Wi-Fi extender. This device can enhance the range of your Wi-Fi network. 

7. Restart your router. 

This will reset your internet connection. If you have them, you should also restart any Wi-Fi range extenders or repeaters. Each device is unique, so you may need to refer to its manual for specific instructions. In general, these are the steps to restart a router: 

• Unplug your modem and router from power. Depending on your setup, you may have a combination modem/router or separate devices. All lights on both should be off. 
  
• Wait approximately 30 seconds, and then plug them back in. 
• Your devices should power on again. Wait a few minutes for the lights on the devices to stabilize. 

Once your router and modem have restarted, try to connect the camera to the app again. 

If your internet is still not working properly, contact your internet service provider and inquire about the service status in your area. 

8. Check for wireless interference. 

The settings on your router or access point may cause connectivity issues. For example, if you have high firewall security or parental controls enabled, they may block new devices from connecting to your Wi-Fi network.  

See if your Wi-Fi router or access point have any of these features enabled. If so, consult the manual to see how you can exclude your camera from these restrictions. 

It depends on your home and what you want to monitor. Keep in mind that if you have a battery camera, you may not want to mount it too high, as you’ll need to remove it to charge the battery.  

Make sure that the location of your camera captures the entire field of view — but because you can set up Activity zones and Blackout zones, you can still adjust what parts of the feed triggers alerts and, for Blackout zones, what part is hidden.  

We don’t recommend it. Aiming your camera through a window can affect the quality of its video or trigger false motion alerts due to reflections in the window's glass. 

Yes. The camera is mounted using a strong magnet. You can easily detach it to recharge it and place it back onto the magnet.

You'll need to be an administrator in your Home. You can see your current permissions in the Philips Hue app by tapping Settings > Account > Home. To become an admin, you can request admin permissions from another admin in the same Home.

Outdoor sensors are not supported as part of the Secure system. When exposed to bright light, such as bright sunlight, the outdoor sensor can trigger a false motion notification. 

Hold the button on the back of the camera for 5 seconds. The camera will make a beeping sound after 2 seconds, and then another after 5 seconds. Release the button after the second beep. Make sure you don't hold the button longer than this, as you will factory reset the camera after 10 seconds.

Here's what your camera's LED lights indicate:

• Blinking blue: Camera is setting up
  
• Steady blue: Camera has established successfully with both the app and Wi-Fi
  
• Red: Camera is recording or live view has been activated
  
• Purple: Camera is booting up
  
• Green: Camera is updating software
  

If you receive a low battery notification, the battery has around 15% battery left. You can wait to charge your camera or you can charge it right away. Connect it to its power supply unit and charge to full power which will take around 7–8 hours.

You'll still be able to use the camera's live view, two-way talk, record video, and receive real-time alerts. However, you won't be able to trigger light alarms from the Philips Hue app or use the camera as a motion sensor.

Your camera may not be getting enough power. Make sure you're using the original power cable that came with the camera. If your camera is part of an outdoor Low-volt setup and powered by a Low-volt power supply unit, ensure that the PSU isn't overloaded: for example, a 40 W PSU can only power up to 40 W of devices. Add the wattage of your outdoor lights, and then add 10–15 W for the camera.

Press and hold the button on the back of the camera for 10 seconds to perform a factory reset. The camera will make a beeping sound after 2, 5, and 10 seconds. Release the button after the third beep.

Be sure the plug itself is functioning correctly and you're using the power supply that came with your camera. If you have a battery camera, make sure that it's fully charged (it should have been connected to power for at least 7–8 hours). 

If the problem persists, factory reset the camera. Press and hold the button on the back of the camera for 10 seconds. The camera will beep three times. After the third beep, release the button. If the camera still doesn't turn on, contact Customer Support.

Yes. If you change your Wi-Fi router or connect the camera to a different Wi-Fi network, your camera will appear offline. Update your Wi-Fi network in the Philips Hue app in Settings > Cameras > Advanced settings > Change Wi-Fi network.

Update your Wi-Fi password in the Philips Hue app in Settings > Cameras > Advanced settings > Change Wi-Fi network. Enter the network again with the password .

Contact your local authorities and file a report about the theft.

Your Secure camera remains locked to your Philips Hue account until it's deleted from your Home. Your data is protected with end-to-end encryption, and cannot be accessed by anyone without your passphrase, meaning your camera will be of no use to a thief if it's not deleted from your app.

When installed at a height of 2 m, the camera has a field of vision of 6 m and 110 degrees. General motion can be detected from far away, while AI alerts, which tell you whether a person, animal, vehicle, or package triggered the motion, require closer proximity to the camera.

You can choose from three levels of motion detection sensitivity. The 6-meter distance is based on the medium setting, which is the default. If you change the sensitivity to high or low, it will affect the detection distance. Note that higher sensitivities will decrease battery life.

Your camera will be updated automatically if it is connected to Wi-Fi. If your camera hasn't been updated in a while, you will be prompted to update it manually. Software updates on the camera are not dependent on any software updates for the Bridge or other Philips Hue devices.

Yes! Secure cameras help you keep an eye on your home — day and night — with a 1080p HD picture and automatic night vision.

Secure cameras have built-in AI features that can detect whether the motion it captures is from a person, animal, vehicle, or package. However, they do not support facial recognition.

If you are watching a video clip, you can change the volume using your mobile device's volume buttons. The volume of the camera is not adjustable.

Yes. By default, night vision is set to automatic mode. You can disable night vision in the Philips Hue app by going to Settings > Camera > Video & audio > Night vision.

Your Secure camera can work on both 2.4 GHz and 5 GHz networks.

For 1080p video, an upload speed of 10–20 Mbps is required. If there isn't enough bandwidth, the video may lag. Make sure that the camera is within range of your Wi-Fi range and does not have any interference. In case your Wi-Fi speed is low, check your bandwidth speed with your internet provider.

Person detection is an advanced feature that comes with a Secure Basic or Plus plan. It uses AI to detect and differentiate between people and other forms of movement, so you can set it to send notifications only if a person is detected — while disregarding motion from pets, for example.

Package detection is an advanced feature that comes with a Secure Basic or Plus plan. It uses AI to detect a package delivery, so you can set it to send notifications only if a delivery is detected — while disregarding movements like those of pets.

Package detection is only possible after setting up the package detection through the Hue app.

Animal detection is an advanced feature that comes with a Secure Basic or Plus plan. It uses AI to detect animals, so you can set it to ignore their movement and limit unnecessary alerts.

To receive advanced alerts that tell you what caused the motion — a person, animal, vehicle, or package — your system needs to be armed.

A Bridge is not needed for camera updates. Unlike other Philips Hue products, the camera updates via Wi-Fi. 

The button does different things when held down for different lengths of time. After each action described below the camera will make a beeping sound. Release the button after the beep.

2 seconds: Restarts the camera and enables Bluetooth connection 

5 seconds: Restarts the camera 

10 seconds: Factory resets the camera 

Every new Secure camera comes with a free, 30-day trial of the Basic plan. The trial starts as soon as the camera is set up, so you can try out all the advanced features that come with a Secure plan.

It takes 7–8 hours to fully recharge a Secure battery camera.

The Secure battery camera is designed to operate in temperatures between -20°C and 45°C. 

If the temperature is below 0°C or above 40°C, the camera may not charge properly. In extreme temperatures (below -20°C or above 45°C, for example), it may enter sleep mode to prevent damage. The camera cannot be woken from this sleep mode while it remains in these temperatures.

The battery of your Secure camera comes partially charged, so you can start using it right away.

The rechargeable battery cannot be replaced. You can charge the Secure battery camera with the power cable that comes with the camera. It takes about 7–8 hours for the camera to fully charge.

Yes! The Secure battery camera will operate normally while it’s charging. Note that while the camera and power cable are weatherproof, the plug is not and should therefore only be used with indoor power outlets.

You can select one of three different battery life modes to use: Best video, Standard, and Best battery life. In the Philips Hue app, go to Settings > Cameras > Battery life. From there, you can select the Best battery life mode. This features the longest battery life by shortening video clip length and lowering video quality and motion sensitivity.  

You can also adjust other camera settings in Settings > Camera Advanced: 

Motion sensitivity: Change the setting to Low. This decreases the camera’s range of detection, which consumes less battery. 

Audio & video: Reduce the video clip recording time.  

Make sure that your camera is not placed too close to busy areas, which can trigger many unnecessary events, or heating vents. Since the camera uses a passive infrared sensor, the change in temperature from the vent may wake the camera from sleep mode unnecessarily. 

To set up a Secure camera, you'll need Wi-Fi, the Wi-Fi password, a Philips Hue account, a Bluetooth-capable mobile device with the Philips Hue app, and the camera's onboarding QR code.

You can read a step-by-step guide.

Set your system to Armed: Away and purposely trigger a contact sensor, indoor motion sensor, or camera. Simply walk around your house and open doors or windows that your contact sensor is on, or walk past an indoor motion sensor or camera. If you receive a notification (provided you have enabled them), your system is working.

Yes! You can mount the camera’s base plate onto a wall or ceiling and attach the camera magnetically to the plate. 

The camera is weather-resistant, so you can use it anywhere inside or outside your home. We recommend placing it near entry points such as the front door, back door, ground-floor windows, driveways, and garages.

For the best results, mount the camera at a height of around 1.5–2 meters. Note that the camera has a motion detection distance of 6–10 meters, depending on the sensitivity setting you choose.

If you're in North America, use the 30 W power supply unit. If you're in Europe, use the 100 W power supply unit. 

Yes! The camera can be mounted at a 60-degree angle in any direction. The camera can’t be parallel to the wall (in other words, it cannot point straight down or up). The mount is magnetic, so you’ll install that first, and then fit the camera onto it.

The camera is weather-resistant and can be mounted outdoors. The power supply that comes with the camera is not rated for outdoor use, so make sure to place the plug indoors. 

Yes. Secure cameras work with Alexa and Google Home, letting you use your voice to control your camera, as well as view its live feed on your smart home devices. Keep an eye on our website and social media to stay up to date on which partners and voice integrations you can use with your cameras.